When your sewing machine refuses to cooperate, you will be confronted with sewing machine problems. What are the likely problems that you might encounter? What are the possible solutions to these technical problems? We shall give technical guides that will keep your mind at rest over the two issues through this article. All you need is to sit back and read through this exclusive takeaway of ours. Enjoy.
Tangled Thread
It is common to encounter a massive nest of tangled thread that appears on the bobbin side of the stitch. It has no bearing on the bobbin. This is caused by improper threading of the sewing machine.
Solution
Apply pressure to the feet. Unthread the entire machine. Now follow the instructions in the manual on the machine and rethread it again fully. Do not thread the machine with the pressure foot down because it will lead to tension in the pressure disk that will lead to other issues.
Sewing machine problems caused by skipped stitches
This problem arises mostly when you use the wrong needle for the fabric that you are sewing. If you use the right needle and it is bent, you are going to encounter the same problem. This occurs when you try to force the fabric rather than allowing the machine to feed it naturally.
Solution
The needle is the cheapest part of the machine accessories. Before you begin sewing, double-check that you are using the correct needle and that it is not bent.
A jammed machine
This is another very common issue that can cause problems when sewing on a machine. It can be resolved by taking some simple steps.
Solution
Remove the fabric that you are sewing under the needle of the machine. Gently tug on the fabric and lift it up to some allowance, then snip off the thread. You will free the fabric from the grip of the thread and needle. How do you go about completely removing the jammed thread? It might require removing the bobbin, the throat, and some other parts. Check the needle and ensure that it is not bent before you continue sewing.
When fabric fails to feed under the needle
The sewing machine is expected to deliver free motion when it is in operation. One of the likely sewing machine problems that you will encounter could be due to the failure of the fabric to feed under the needle. There are several factors that contribute to sewing machine feeding issues.
Solution
Check the feed dog on the machine. Reduce the dog’s feed intake by adjusting the setting. If your machine does not have a setting for feeding the dog, remove the throat plate and have it cleaned. You can now oil the machine according to the instructions in the manual for the machine. If the process does not work for you, then troubleshoot the issue through the manual. If that fails, you need to call in the experts for repair work.
Poor feed
If you are constantly experiencing poor feeding, there is something wrong with the technique you are employing when operating the machine.
Solution
Allow the feeding dogs to perform their duties. Make it a habit not to force the fabric into the machine.
Shredding Thread
The embracement caused by breaking a thread while the machine is running is better imagined than felt. If not addressed, it can suffocate one’s enthusiasm for one’s job.
Solution
- If the problem is linked to a thread hanging up on the thread spool, change the direction of the feed of the thread through the spool.
- Check your thread to ensure that you are not using a weak or old thread. If that is the case, simply change the thread to a new one and you are good to go!
- Check your needle to ensure that it is working properly. Specialty needles have wider paths and are appropriate for special threads.
Fusing threads cause sewing machine issues.
When the machine stops, you may likely experience a fusing thread.
Solution
You can use a better quality thread if the issue is caused by an incorrect thread. If the fabric is poorly finished, you can use different needles and needle coolants to get better results. If the needle is damaged or overheated, replace it properly.
When the sewing machine seizes up
You need to give your machine a little bit of effort to start turning. If the little push you give the machine fails to bring it into action, you are advised to stop the sewing process.
Solution
Your fabric may be too tough for your machine; remove the fabric. If that is not the problem, then check your needle and make sure you are working with the right needle. If the first two processes fail, consult your manual or an expert.
Conclusion
We have gone through likely areas of sewing machine problems. The solutions to each of the eight problems addressed above have been given. You will easily overcome any challenge with our professional tips above.